feature s ACTF8092 - f864w - dcc6c ? low - loss rf filter ? high rejection ? single ended operation at 50 without m atching ? ceramic package for s urface m ounted t echnology ( smt ) ? lead- f ree p roduction and rohs c ompliance package dimension s ceramic package: dcc6 c pin configuration 2 input 5 output 1, 3, 4, 6 case ground 1, 3, 4, 6 to be grounded marking top view, laser marking " actf ?: manufacturer?s mark ? f ?: saw filter ? 8092 ?: part number ? ?: terminal 1 ??: lot number (the code shown below varies in a 4 - year cycle) code 1 2 3 4 5 6 7 8 9 10 11 12 2009 a b c d e f g h j k l m 2010 n p q r s t u v w x y z 2011 a b c d e f g h i j k m 2012 n p q r s t u v w x y z maximum ratings rating value unit opera ting t emperature r ange t a -40 ~ + 8 5 c storage t emperature r ange t stg - 40 ~ +85 c dc v oltage ( between any t erminals ) v dc 5 v rf power ( in bw ) p 1 8 dbm esd voltage (hb) v esd 150 v actf* 8092f
electrical characteristics ( - 4 0 c ~ +85 c ) item minimum typical maximum unit center frequency f c - 86 6 . 5 0 - mhz maximum insertion loss in 865 .0 ~ 868 .0 mhz il - 2. 8 3.5 db maximum insertion loss in 863.0 ~ 870.0 mhz il - 2. 8 3.8 db absolute attenuation 0.300 0 ? 830 .0 0 mhz 40 44 - db 830.0 0 ? 84 5 .0 0 mhz 38 44 - db 8 80.0 0 ? 8 84 .30 mhz 50 60 - db 884.0 0 ? 88 7 .0 0 mhz 50 60 -- db 887.0 0 ? 965 .0 0 mhz 38 42 db 965.0 0 ? 1500 .0 0 mhz 42 47 db passband ripple ? 865.0 ~ 868.0 mhz 0.6 1.0 db passband ripple ? 863.0 ~ 870.0 mhz 0.7 2.0 db source / load impedance (single ended) 50 rohs c ompli an t electrostatic sensitive device typical frequency response
stability c haracteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10 ~ 55hz (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40 c , 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70c for 16 hours (b) +55 c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40 c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high t emperature e xposure (a) temperature: 70 c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70 c for 30 minutes ? -25 c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements : the saw filer shall remain w ithin the electrical specifications after tests.
remarks ? saw devices should not be used in any type of fluid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do not operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be avoided, deterioration of the characteristics c an occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering iron on the body of components. ? be careful not to subject the terminals or leads of components to excessive force. ? saw devices are electrostatic sensitive . p lease avoid static voltage during operation and storage. ? u ltrasonic cleaning shall be avoided . ultrasonic vibration may ca use destruction of components . test circuit recommended land pattern 50 / 50 configuration
packing information carrier tape reel dimensions outer packing type quantity dimension description weight carton box 0.85 carton box 1 0000 190190190 1. 7 0 unit: mm unit: kg
recommended soldering profile 1. the specifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wave (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies.
|
